- advanced programmable interrupt controller (APIC) mode
- setting
- Installing RHEL 6 on an Altix UV System
- Determining the System APIC Mode
- Altix UV server software installation
- SGI Altix UV Server Installation Instructions
- BaseIO VGA
- Enabling BaseIO VGA
- booting from Fibre Channel disk
- Booting from Fibre Channel Disk
- booting using iSCSI protocol
- Booting Using iSCSI Protocol
- command
- power reset
- Setting an Administrative Password on the Console
- console
- exiting
- Setting an Administrative Password on the Console
- setting an administrative password
- Setting an Administrative Password on the Console
- determining the system APIC mode
- Determining the System APIC Mode
- determining the system BIOS level
- Determining the System BIOS Level from the Boot Manager
- DVD access
- DVD Access
- EFI utility
- commands
- drivers
- Booting from Fibre Channel Disk
- map
- Booting from Fibre Channel Disk
- reset
- Booting from Fibre Channel Disk
- set
- Booting from Fibre Channel Disk
- enabling BaseIO VGA
- Enabling BaseIO VGA
- exit console
- Setting an Administrative Password on the Console
- Fibre Channel
- booting
- Booting from Fibre Channel Disk
- Fibre Channel Card EFI utility
- Booting from Fibre Channel Disk
- install RHEL 6
- Install and Configure RHEL 6 and SGI Foundation 2.4 Software
- install SLES11 on the system management node
- Install and Configure SLES 11 SP1 and SGI Foundation 2.4 Software
- install software
- Altix UV server
- SGI Altix UV Server Installation Instructions
- SGI Management Center
- SGI Management Center Software Installation
- SLES 11 SP1, SGI Foundation 2.4 , and SGI Performance Suite 1.2
- Installing SLES 11 SP1, SGI Foundation 2.4, and SGI Performance
Suite 1.2 Software Together
- system management node
- System Management Node Software Installation
- installing RHEL 6
- Installing RHEL 6 on an Altix UV System
- installing RHEL 6 on the system management node
- Install and Configure RHEL 6 and SGI Foundation 2.4 Software
- introduction
- Altix UV Software Installation
- iSCSI
- booting
- Booting Using iSCSI Protocol
- navigate the device manager
- Setting an Administrative Password on the Console
- NUMAlink
- disable or enable
- Installing RHEL 6 on an Altix UV System
- power reset command
- Setting an Administrative Password on the Console
- remote console
- enabling
- Installing SLES 11 SP1, SGI Foundation 2.4, and SGI Performance
Suite 1.2 Software Together
- Installing RHEL 6 on an Altix UV System
- setting an administrative password on the console
- Setting an Administrative Password on the Console
- SGI Altix UV 1000 system rack
- System Management Node Software Installation
- SGI KVM console
- Enabling BaseIO VGA
- SGI Management Center software installation
- SGI Management Center Software Installation
- SGI management node RPMs
- SMN RPMs for SSI
- SLES 11 SP1, SGI Foundation 2 SP1, and SGI Performance Suite 1.2 software installation
- Installing SLES 11 SP1, SGI Foundation 2.4, and SGI Performance
Suite 1.2 Software Together
- system BIOS level
- Determining the System BIOS Level from the Boot Manager
- system configuration
- Enabling BaseIO VGA
- system management node (SMN)
- Install and Configure SLES 11 SP1 and SGI Foundation 2.4 Software
- system management node software installation
- System Management Node Software Installation
- VGA
- Enabling BaseIO VGA
- YaST2 firstboot installer
- Install and Configure SLES 11 SP1 and SGI Foundation 2.4 Software
- YaST2 installation tool
- Install and Configure SLES 11 SP1 and SGI Foundation 2.4 Software
- YaST2 system configuration editor
- Enabling BaseIO VGA