MicroVAX II 630QB Technical Manual

Company:Digital Equipment Corporation
Part:AZ-GLBAA-MN
Date:1985-11
Keywords:

Table of Contents

  • Chapter 1 BA123-A Enclosure
    • 1.1 Introduction
    • 1.2 Enclosure Frame
    • 1.3 Control Panel
      • 1.3.1 Mass Storage Shelves
      • 1.3.2 CPU Console Board
    • 1.4 Signal Distribution Board
    • 1.5 Backplane
    • 1.6 Power Supply
    • 1.7 I/O Distribution Panel
  • Chapter 2 Base System
    • 2.1 Introduction
    • 2.2 KA630-A CPU
      • 2.2.1 Console Program
      • 2.2.2 Primary Bootstrap Program (VMB)
      • 2.2.3 CPU Patch Panel Insert
    • 2.3 MS630 Memory Module
  • Chapter 3 System Options
    • 3.1 Introduction
      • 3.1.1 Ordering Options
      • 3.1.2 Module Configuration
    • 3.2 Communications
      • 3.2.1 DEQNA Ethernet Interface
      • 3.2.2 DHV11 Asynchronous Multiplexer (Eight Lines)
      • 3.2.3 DHV11 Remote Distribution Cabinet Kit (CK-DHV11-VA)
      • 3.2.4 DLVJ1 Asynchronous Interface (Four Lines)
      • 3.2.5 DMV11 Synchronous Controller
      • 3.2.6 DPV11 Synchronous Interface
      • 3.2.7 DRV11-J High Density Parallel Interface (Four Lines)
      • 3.2.8 DZQ11 Asynchronous Multiplexer (Four Lines)
      • 3.2.9 DZV11 Asynchronous Multiplexer (Eight Lines)
      • 3.2.10 LPV11 Interface Module (For LP25 System Printer)
    • 3.3 Disk Storage
      • 3.3.1 RQDX2, RQDX3 Disk Controllers
      • 3.3.2 RD52, RD53 Disk Drives
        • 3.3.2.1 Factory Configuration
        • 3.3.2.2 Disk Formatting
      • 3.3.3 RX50 Diskette Drive
    • 3.4 Tape Storage
      • 3.4.1 TK50 Tape Drive Subsystem
  • Chapter 4 Configuration
    • 4.1 Configuration Rules
      • 4.1.1 Module Physical Priority
      • 4.1.2 Expansion Space
        • 4.1.2.1 Backplane
        • 4.1.2.2 I/O Distribution Panel Insert Space
      • 4.1.3 Power Requirement
      • 4.1.4 Bus Loads
      • 4.1.5 Module CSR Addresses and Interrupt Vectors
    • 4.2 Configuration Examples
  • Chapter 5 Diagnostics
    • 5.1 Introduction
    • 5.2 KA630-A Boot and Diagnostic ROM
      • 5.2.1 Power-up Mode
      • 5.2.2 Console Mode
      • 5.2.3 Console Terminal Error Messages
    • 5.3 Power-Up LEDs On Mass Storage, Backup, and Communications Devices
    • 5.4 MicroVAX Maintenance System
      • 5.4.1 Test the System (Menu Item #1)
      • 5.4.2 Display System Configuration and Devices (Menu Item #2)
      • 5.4.3 Display the Utilities Menu (Menu Item #3)
      • 5.4.4 Display the Service Menu (Menu Item #4)
      • 5.4.5 Exit the MicroVAX Maintenance System (Menu Item #5)
    • 5.5 Troubleshooting
      • 5.5.1 Unknown System Level Problems (System Fails to Boot)
      • 5.5.2 Device-Specific Problems
  • Chapter 6 FRU Removal and Replacement Procedures
    • 6.1 Introduction
    • 6.2 Removal of the Exterior Panels
      • 6.2.1 Removal of the Right Side Panel
      • 6.2.2 Removal of the Left Side Panel
    • 6.3 On/Off Switch Removal
    • 6.4 CPU Console Board Removal
    • 6.5 13.3 cm (5.25 in) Mass Storage Device Removal
      • 6.5.1 RD52 Read/Write Board Removal
      • 6.5.2 RD53 Read/Write Board Removal
    • 6.6 Fan Removal
      • 6.6.1 Mass Storage Fan Removal
      • 6.6.2 Card-Cage Fan Removal
    • 6.7 Module Removal
    • 6.8 Door Interlock Switch Removal
    • 6.9 Temperature Sensor Removal
    • 6.10 Power Supply Removal
    • 6.11 Backplane Removal
    • 6.12 Filter Connector Removal
  • Appendix A Console Commands
  • Appendix B Console Error Messages and Explanations

Copies

Address: http://www.computer.museum.uq.edu.au/pdf/AZ-GLBAA-MN%20MicroVAX%20II%20630QB%20Technical%20Manual.pdf
Site: Wilber Williams' Computer Museum
Format: PDF
Size: 13121717 bytes (12.5 MiB)
MD5: a46f0f96d7ba5dccb59af3d8b4dc69b3
Mirrors: