AD01-D Analog-to-Digital Conversion Subsystem Manual

Company:Digital Equipment Corporation
Part:DEC-11-HADB-D
Date:1972-06
Keywords:PDP-11

Table of Contents

  • Chapter 1 General Information
    • 1.1 Introduction
    • 1.2 Purpose
    • 1.3 Functional Description
    • 1.4 Physical Description
    • 1.5 Specifications
      • 1.5.1 Environmental
      • 1.5.2 Power Requirements
      • 1.5.3 Packaging
      • 1.5.4 Performance Parameters
    • 1.6 Reference Documents
  • Chapter 2 Installation and Adjustments
    • 2.1 Installation Planning
    • 2.2 Environmental Requirements
    • 2.3 Configurations
      • 2.3.1 Channel Expansion
      • 2.3.2 Bipolar Option AH05
      • 2.3.3 Sample and Hold Amplifier Option AH04
      • 2.3.4 Unibus Connections
      • 2.3.5 Multiplexer Channel Connections
      • 2.3.6 External Clock Connection
    • 2.4 Installation Procedure
    • 2.5 Option Installation
    • 2.6 Adjustment Procedure
      • 2.6.1 Power Supply Adjustments
      • 2.6.2 Timing Adjustment
      • 2.6.3 A/D Converter
        • 2.6.3.1 A812
        • 2.6.3.2 A862 (AH05 Option)
      • 2.6.4 Sample and Hold A405 (AH04 Option)
        • 2.6.4.1 AH04 Option Only
        • 2.6.4.2 AH04 with AH05 Option Only
      • 2.6.5 Switched-Gain Amplifier A220
      • 2.6.6 Multiplexer Setup
      • 2.6.7 External Sync
  • Chapter 3 Operation and Programming
    • 3.1 Introduction
    • 3.2 Address Format
    • 3.3 CSR Format
    • 3.4 DBR Format
    • 3.5 Interrupt Structure
    • 3.6 External Clock Control
      • 3.6.1 EXT IN
      • 3.6.2 EXT IN A
      • 3.6.3 External Clock Timing Considerations
  • Chapter 4 Principles of Operation
    • 4.1 Introduction
    • 4.2 Block Diagram Analysis
    • 4.3 Detailed Circuit Analysis
      • 4.3.1 Multiplexer
      • 4.3.2 Scaling Amplifier
      • 4.3.3 A/D Converter
        • 4.3.3.1 Unipolar with Wide Aperture
        • 4.3.3.2 Unipolar with Narrow Aperture
        • 4.3.3.3 Bipolar with Wide Aperture
        • 4.3.3.4 Bipolar with Narrow Aperture
      • 4.3.4 Timing
      • 4.3.5 Bus Interface
  • Chapter 5 Maintenance
    • 5.1 AD01-D MainDEC-11-D6AB Diagnostic Program
    • 5.2 Preventive Maintenance
      • 5.2.1 Preventive Maintenance Tasks
    • 5.3 Corrective Maintenance
      • 5.3.1 Preliminary Investigation
      • 5.3.2 System Troubleshooting
      • 5.3.3 Logic Troubleshooting
      • 5.3.4 Circuit Troubleshooting
      • 5.3.5 Validation Tests
      • 5.3.6 Recording
    • 5.4 Test Equipment
    • 5.5 Module Handling and Repair
    • 5.6 Spare Parts
  • Chapter 6 Engineering Drawings
  • Appendix A 10-Bit Unipolar Calibration Chart
  • Appendix B 11-Bit Bipolar Calibration Chart

Copies

Address: http://www.mainecoon.com/classiccmp/AD01-D/AD01-D%20manual%20part-1.tif
Site: Chris Kennedy's archive of Henk Gooijen's scans
Format: TIFF
Size: 4675534 bytes (4.5 MiB)
MD5: a85e2ddd660a0df3746a99c212e443c6
Notes: Part 1 of 2: Chapters 1 to 3
Credits:Scanned by Henk Gooijen
 
Address: http://www.mainecoon.com/classiccmp/AD01-D/AD01-D%20manual%20part-2.tif
Site: Chris Kennedy's archive of Henk Gooijen's scans
Format: TIFF
Size: 4702206 bytes (4.5 MiB)
MD5: d4dddf49baa6935f543159980960dc90
Notes: Part 2 of 2: Chapter 4 to end
Credits:Scanned by Henk Gooijen
 
Address: http://manx-docs.org/collections/hcps/AD01_manual.pdf
Site: hcps collection
Format: PDF
Size: 9701975 bytes (9.3 MiB)
MD5: b5159396e9c2c30f40ca571fd4000555