MicroVAX II 630QY, 630QZ Technical Manual

Company:Digital Equipment Corporation
Part:AZ-FE06A-TN
Date:1985-04
Keywords:

Table of Contents

  • Chapter 1 BA23-A Enclosure
    • 1.1 Introduction
    • 1.2 BA23-A Frame
      • 1.2.1 Air Circulation
    • 1.3 Front Control Panel
      • 1.3.1 Control Panel Printed Circuit Board
    • 1.4 Mass-Storage
    • 1.5 Backplane
      • 1.5.1 Mass-Storage Signal Distribution Panel
      • 1.5.2 H9278 Backplane
    • 1.6 Power Supply and Fans
    • 1.7 Rear I/O Distribution Panel
  • Chapter 2 Base System
    • 2.1 Introduction
    • 2.2 KA630-A CPU
      • 2.2.1 Console Program
      • 2.2.2 Primary Bootstrap Program
      • 2.2.3 CPU Patch Panel Insert
    • 2.3 MS630 Memory Module
  • Chapter 3 System Options
    • 3.1 Introduction
      • 3.1.1 Ordering Options
      • 3.1.2 Module Configurations
    • 3.2 Communications
      • 3.2.1 DEQNA Ethernet Interface
      • 3.2.2 DHV11 Asynchronous Multiplexer (eight lines)
      • 3.2.3 DLVJ1 Asynchronous Multiplexer (four lines)
      • 3.2.4 DMV11 Synchronous Controller
      • 3.2.5 DPV11 Synchronous Interface
      • 3.2.6 DRV11-J High Density, Parallel Interface (four lines)
      • 3.2.7 DZQ11 Asynchronous Multiplexer (four lines)
      • 3.2.8 DZV11 Asynchronous Multiplexer (eight lines)
      • 3.2.9 LPV11 Interface Module
    • 3.3 Disk Storage Devices
      • 3.3.1 RQDX2 Disk Controller
      • 3.3.2 RD51, RD52, RD53 Disk Drives
        • 3.3.2.1 Factory Configuration
      • 3.3.3 RX50-AA Diskette Drive
      • 3.3.4 RC25 Disk Subsystem
      • 3.3.5 TK50 Tape Drive Subsystem
  • Chapter 4 Configuration
    • 4.1 Configuration Rules
      • 4.1.1 Module Physical Priority
      • 4.1.2 Expansion Space
      • 4.1.3 Power Requirements
      • 4.1.4 Bus Loads
      • 4.1.5 Module CSR Addresses/Interrupt Vectors
        • 4.1.5.1 Floating CSR Addresses
    • 4.2 Configuration Examples
      • 4.2.1 Base System Configuration
      • 4.2.2 Advanced System Configuration
  • Chapter 5 Diagnostics
    • 5.1 Introduction
    • 5.2 KA630 Boot and Diagnostic ROM
      • 5.2.1 Power-up Mode
      • 5.2.2 Console Mode
    • 5.3 Power-up LEDs on Mass Storage, Backup, and Communications devices
    • 5.4 MicroVAX Maintenance System
      • 5.4.1 Configuration Verification
      • 5.4.2 System Tests
    • 5.5 Troubleshooting
      • 5.5.1 Unknown System Level Problems
      • 5.5.2 Device-Specific Problems
  • Chapter 6 FRU Removal and Replacment Procedures
    • 6.1 Introduction
    • 6.2 Control Panel Removal
    • 6.3 RX50/TK50 Drive Removal
      • 6.3.1 TK50/TQK50 Interconnect Cable Removal and Installation
    • 6.4 RD5n Fixed Disk Drive Removal
      • 6.4.1 RD51 Disk Drive Read/Write Board Removal
      • 6.4.2 RD52 Main Printed Circuit Board Removal
      • 6.4.3 RD53 Disk Drive Device Electronics Board Removal
      • 6.4.4 RD5n/RDQX Interconnect Cable Removal and Installation
    • 6.5 Backplane Assembly Removal
    • 6.6 Power Supply (H7864-A) Removal
    • 6.7 Rear Cooling Fan Removal
    • 6.8 Front Fan Removal
    • 6.9 Module Removal
    • 6.10 Rear I/O Insert Panel Removal
    • 6.11 Time of Year Clock Battery Backup Removal
  • Appendix A Console Commands
  • Appendix B Console Error Messages and Explanations

Copies

Address: http://manx-docs.org/collections/hcps/fe06atn.pdf
Site: hcps collection
Format: PDF
Size: 36678487 bytes (35.0 MiB)
MD5: 62e3a4e07454f4979296976e68e18227